POTENTIOSTAT / GALVANOSTAT
The Interface 1010 is a value oriented, general purpose potentiostat for almost all applications except for high current electrochemistry.
The "T(eaching)" version of the Interface 1010 can be purchased flexibly at a low entry level budget for almost all applications in electrochemical research and -industry. Later, if requirements increase, existing electronic components with higher specifications can be activated by means of a paid upgrade.
The Interface 5000 Potentiostat / Galvanostat / ZRA is a compact, inexpensive system for material development and condition testing of batteries, super capacitors and fuel cells
The Interface 5000 delivers a higher current of ± 5A in direct comparison with the Interface 1010. The maximum available working electrode potential is ± 6V. The additional electrometer allows the simultaneous tracking of both half cells of a battery, a supercapacitor or a fuel cell when using an embedded reference electrode including the whole cell in a single experiment. Due to this time saving additional experiments can be scheduled.
The latest development in the Reference 600 series - the Reference 620 - features 20-bit analog/digital conversion, gaining about a decade of additional sensitivity. This makes the system the first choice for demanding applications, e.g. in basic research.
The Reference 620 offers eleven current ranges between 60 pA - 600 mA at a maximum of ± 12 V at the working electrode. Two additional gain stages (10x / 100x) extend to an even broader current range of 13 decades, allowing electrochemical impedance spectroscopy (EIS) on very high ohmic surrogates between 5 MHz and 10 µHz with current resolutions down to 20 aA per bit using state-of-the-art microelectronics and oversampling. Careful selection of electronic components and design result in...
The high-end potentiostat for all demanding applications in electrochemistry from very low to high currents.
The Reference 3000 offers eleven current ranges between 300 pA - 3000 mA at a maximum of either ±3A@±15V or ±1.5A@±32V at the working electrode. Two additional gain stages (10x / 100x) extend to an even broader current range of 13 decades, allowing electrochemical impedance spectroscopy (EIS) on very high ohmic surrogates between 1 MHz and 10 µHz with current resolutions down to 100 aA per bit using state-of-the-art microelectronics and oversampling. Careful selection of electronic components and design result...
The well-known high-end Reference 3000AE Potentiostat/Galvanostat/ZRA with eight additional auxiliary electrometers (AE).
With the eight additional channels of the Auxiliary Electrometer (AE) add-on option of the Reference 3000 Potentiostat / Galvanostat / ZRA, potential differences of either eight individual half cells of a stack or up to eight peripherical signal transducers can be measured. Each of the eight available electrometers (± 5 V vs. counter electrode potential) can clarify the impedance of a half cell in an electrochemical impedance spectroscopy measurement performed over the entire stack or to simply measure eight additional...
The Reference 3000 (AE) Potentiostat/Galvanostat/ZRA high performance and multi-purpose basic unit can be combined with the Reference 30k Booster and is ideal for evaluating new highest-level technologies for batteries, fuel cells, supercapacitors and high turnover electrochemical synthesis.
The Reference 3000 is already a high-performance system, but with the addition of the Reference 30k booster, it can serve even more demanding applications. You can therefore make a valuable contribution at the highest level in basic research, electrochemical synthesis, and electrochemical energy storage. The Reference 3000 basic instrument can either be equipped later with 8 additional auxiliary electrometers (AE; Auxilliary Electrometer) by means of a hardware upgrade, or you can opt for the Reference 3000AE.
GAMRY ACCESSORIES FOR ELECTROCHEMISTRY
The MK 3 simulates with high accuracy typical fuel cell conditions for conductivity measurements via electrochemical impedance spectroscopy in combination with the Gamry System Reference 600+ or Interface 1010E.
The fumatech MK 3 conductivity cell is designed for measuring the proton conductivity and the general ionic conductivity of membrane samples in a temperature range from room temperature up to 200°C with an additional potentiostat. The measurements can be performed under selected humidification as well as in dry condition. Suitable potentiostats for operation with the MK 3 are e.g. the Gamry Reference 600+ Potentiostat/Galvanostat/ZRA or the Gamry Interface 1010E Potentiostat/GalvanostatZRA).
RDE710 Rotator for RDE, RRDE and RCE is designed for hydrodynamically controlled electrode reactions both for the characterization of catalysts and for determining flow-induced corrosion rates.
The RDE710 - Rotating Disk (RDE), Ring Disk (RRDE) or Cylinder Electrode (RCE) from Gamry is a fast DC permanent magnet motor with low inertia. Between 50 rpm and 10.000 rpm, a wide variety of materials in coordination with the shaft and electrodes can be controlled manually or digitally in conjunction with a potentiostat.
HOT DISK - MEASUREMENT DEVICES
The Hot Disk TPS 2500 S is the flagship instrument in the system portfolio of Hot Disk AB and covers an extensive range of materials of various geometries and dimensions - meets ISO Standard 22007-2.
This general-purpose R&D instrument is designed for precision analysis of thermal transport properties – including thermal conductivity, thermal diffusivity and specific heat capacity. The TPS 2500S covers the range from 5 mW/mK to 1800 W/mK and with the possibility of very short measurement times you can run also very small bulk samples, thin films or coatings.
Testing the extreme – when you have very small and very high conductive samples this is the ideal instrument for testing heat conductivity, thermal diffusivity and specific heat.
The capabilities of TPS 3500 go well beyond that of any other Hot Disk instrument to date, while retaining the documented precision of all TPS thermal conductivity meters. Short measurement times down to 0,1 second and high end electronics enables measurements on extrem good heat conducting as well as small samples - it meets ISO 22007-2.
PLANETARY MIXERS WITHOUT VACUUM
Mixing and defoaming without vacuum in one step – with patented defoaming mode
Our top-selling planetary centrifugal mixer. Highly efficient without stirrer. Defoaming is often possible without vacuum. The device sports a Mixing and a Defoaming Mode, which differ in the ratio between the two circular movements.
Mixing and defoaming without vacuum in one step
Our entry-level planetary centrifugal mixer. Highly efficient mixing without stirrer.
SOLDER PASTE MIXERS
Mixing, warming and defoaming of solder paste – without vacuum in one single step.
A planetary mixer, designed especially for solder pastes and similar media like screen printing. The samples are homogenized, deaerated and warmed up by overlaying the two rotation movements. Unlike the allrounder ARE-250, the maximum load is about doubled, to enable the use of 500 g net standard solder paste containers. The maximum speed is likewise reduced to 1.200 RPM, which is completely enough for solder pastes. This makes the SR-500 the Thinky mixer with the best value in our portfolio.
CALORIMETER FOR MATERIALS RESEARCH/LIFE SCIENCE
The universal and modular calorimeter for materials research and life science
The I-Cal Flex’s flexible sample cell configuration lets users choose between up to 8 sample cells of 20 ml capacity for homogeneous food items, or up to 2 sample cells of 450 ml capacity, with sample vials suitable for large inhomogeneous samples such as soils, fruits, meats and other food items, minerals, small insects, crops and seeds, sludges, cement or concrete, and others. The I-Cal Flex's isothermal temperature can be set as low as 2°C and it offers the best...
